View SP7650EB_750740.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SP7650 Evaluation Board Manual
Easy Evaluation for the SP7650ER 12V Input, 0 to 3A Output Synchronous Buck Converter Built in Low Rds(on) Power FETs UVLO Detects Both VCC and VIN High Integrated Design, Minimal Components High Efficiency: 90% Feature Rich: UVIN, Programmable Softstart, External VCC Supply and Output Dead Short Circuit Shutdown SP7650EB SCHEMATIC
U1 SP7650
1 PGND PGND PGND GND VFB COMP UVIN GND SS VIN VIN VIN VIN LX LX LX LX VCC GND GND GND BST NC LX LX LX 26 25 24 23 22 21 20 19 18 17 16 15 14 2 3 4 5 6 7 8 9
L1 6.8uH C3 22uF 6.3V CVCC 2.2uF RBST 20 DBST SD101AWS CBST 6,800pF RZ3 7.15k,1% CZ3 150pF
CZ2
RZ2
1,000pF 15k,1% CP1 22pF CF1 100pF fs=300Khz
VOUT 3.30V 0-3A
R1 68.1k,1%
GND2
C3 CERAMIC 1210 X5R R2 21.5k,1%
CSS 47nF
10 11 12 13
12V VIN
C1 CERAMIC 1210 X5R R3 200k,1% C1 22uF 16V R4 100k,1%
R6 464,5% 1210 C2 0.1uF
Notes:
D1 BZX384B5V6 Vz=5.6V U1 Bottom-Side Layout should has three Contacts which are isolated from one of another, QT & QB Drain Contact and Controller GND Contact All resistor & capacitor size 0603 unless other wise specify
GND
Date: 01/04/05
SP7650 Evaluation BoardManual
Copyright 2005 Sipex Corporation
USING THE EVALUATION BOARD 1) Powering Up the SP7650EB Circuit Connect the SP7650 Evaluation Board with an external +12V power supply. Connect with short leads and large diameter wire directly to the "VIN" and "GND" posts. Connect a Load between the VOUT and GND2 posts, again using short leads with large diameter wire to minimize inductance and voltage drops. 2) Measuring Output Load Characteristics It's best to GND reference scope and digital meters using the Star GND post in the center of the board. VOUT ripple can best be seen touching probe tip to the pad for C3 and scope GND collar touching Star GND post - avoid a GND lead on the scope which will increase noise pickup. 3) Using the Evaluation Board with Different Output Voltages While the SP7650 Evaluation Board has been tested and delivered with the output set to 3.30V, by simply changing one resistor, R2, the SP7650 can be set to other output voltages. The relationship in the following formula is based on a voltage divider from the output to the feedback pin VFB, which is set to an internal reference voltage of 0.80V. Standard 1% metal film resistors of surface mount size 0603 are recommended. Vout = 0.80V ( R1 / R2 + 1 ) => R2 = R1 / [ ( Vout / 0.80V ) - 1 ] Where R1 = 68.1K and for Vout = 0.80V setting, simply remove R2 from the board. Furthermore, one could select the value of R1 and R2 combination to meet the exact output voltage setting by restricting R1 resistance range such that 50K R1 100K for overall system loop stability. Note that since the SP7650 Evaluation Board design was optimized for 12V down conversion to 3.30V, changes of output voltage and/or input voltage will alter performance from the data given in the Power Supply Data section. In addition, the SP7650ER provides short circuit protection by sensing Vout at GND. POWER SUPPLY DATA The SP7650ER is designed with a very accurate 1.0% reference over line, load and temperature. Figure 1 data shows a typical SP7650 Evaluation Board Efficiency plot, with efficiencies to 90% and output currents to 3A. SP7650ER Load Regulation is shown in Figure 2 of only 0.1% change in output voltage from no load to 3A load. Figures 3 and 4 illustrate a 1.5A to 3A and 0A to 3A Load Step. Start-up Response in Figures 5, 6 and 7 show a controlled start-up with different output load behavior when power is applied where the input current rises smoothly as the Softstart ramp increases. In Figure 8 the SP7650ER is configured for hiccup mode in response to an output dead short circuit condition and will Softstart until the over-load is removed. Figure 9 and 10 show output voltage ripple less than 40mV at no load to 3A load. While data on individual power supply boards may vary, the capability of the SP7650ER of achieving high accuracy over a range of load conditions shown here is quite impressive and desirable for accurate power supply design.
2
Efficiency vs Load
100
Load Regulation 3.305 O utput Voltage (V)
E fficien cy (% )
95 90 85 80 1.0 1.5 2.0 2.5 3.0
3.300
Vin=12V Vout=3.3V
3.295
Vin=12V Vout=3.3V
0.5 1.0 1.5 2.0 Load Current (A) 2.5 3.0
3.290
Load Current (A)
Figure 1. Efficiency vs Load
Figure 2. Load Regulation
Vout Vin Iout (2A/div)
Vout
Vin Iout (2A/div) Vin=12V Vout=3.3V
Vin=12V Vout=3.3V
Figure 3. Load Step Response: 1.5->3A
Figure 4. Load Step Response: 0->3A
Vout Vin SoftStart
Vout
Vin
SoftStart
Iout (2A/div) Iout (2A/div)
Figure 5. Start-Up Response: No Load
Figure 6. Start-Up Response: 1.5A Load
Vout SoftStart Vin SoftStart Vout Iout (2A/div) Ichoke (5A/div)
Figure 7. Start-Up Response: 3A Load
Figure 8. Output Load Short Circuit
3
+5V BIAS SUPPLY APPLICATION SCHEMATIC In this application example, the SP7650ER is power by an external +5V bias supply which current consumption of 20mA Maximum. If this supply is not available than it is recommend Sipex SPX5205 Low-Noise LDO Voltage Regulator.
U1 SP7650
1 PGND PGND PGND GND VFB COMP UVIN GND SS VIN VIN VIN VIN LX LX LX LX VCC GND GND GND BST NC LX LX LX 26 25 24 23 22 21 20 19 18 17 16 15 14 2 3 4 5 6 7 8 9
L1 6.8uH C3 22uF 6.3V RZ3 7.15k,1% CZ3 150pF
CZ2
RZ2
1,000pF 15k,1% CP1 22pF CF1 100pF fs=300Khz
VOUT 3.30V 0-3A
R1 68.1k,1%
CVCC 2.2uF 20 SD101AWS DBST CBST 6,800pF
GND2
C3 CERAMIC 1210 X5R R2 21.5k,1%
CSS 47nF
10 11 12
RBST
VIN 12V
C1 CERAMIC 1210 X5R C1 22uF 16V
13
R3 200k,1%
Notes:
U1 Bottom-Side Layout should has three Contacts which are isolated from one of another, QT & QB Drain Contact and Controller GND Contact All resistor & capacitor size 0603 unless other wise specify
+5V
GND
R4 100k,1%
C2 0.1uF
Vout ripple = 32mV
Vout ripple = 40mV
Vin
Vin
Ichoke(2A/div)
Ichoke (2A/div)
Figure 9. Output Ripple: No Load
Figure 10. Output Ripple: 3A Load
Table 1: SP7650EB Suggested Components and Vendor Lists
4
TYPE III LOOP COMPENSATION DESIGN The open loop gain of the SP7650EB can be divided into the gain of the error amplifier Gamp(s), PWM modulator Gpwm, buck converter output stage Gout(s), and feedback resistor divider Gfbk. In order to crossover at the selecting frequency fco, the gain of the error amplifier has to compensate for the attenuation caused by the rest of the loop at this frequency. The goal of loop compensation is to manipulate the open loop frequency response such that its gain crosses over 0dB at a slope of -20dB/dec. The open loop crossover frequency should be higher than the ESR zero of the output capacitors but less than 1/5 to 1/10 of the switching frequency fs to insure proper operation. Since the SP7650EB is designed with Ceramic Type output capacitors, a Type III compensation circuit is required to give a phase boost of 180 in order to counteract the effects of the output LC under damped resonance double pole frequency.
Type III Voltage Loop Compensation Gamp(S) Gain Block Vref (Volts)
(SRz2Cz2+1)(SR1Cz3+1) SR1Cz2(SRz3Cz3+1)(SRz2Cp1+1)
PWM Stage Gpwm Gain Block
Vin Vramp_pp
Output Stage Gout(S) Gain Block
(SResrCout+1) [S^2LCout+S(Resr+Rdc)Cout+1]
Vout (Volts)
Voltage Feedback Gfbk Gain Block
R2 OR (R1+R2) Vref Vout
Vfbk (Volts) Definitions: Resr Rdc
:= Output Capacitor Equivalent Series Resitance := Output Inductor DC Resistance
Vramp_pp := SP7650 Internal RAMP Amplitude Peak to Peak Voltage Conditions: Cz2 >> Cp1 and R1 >> Rz3 Output Load Resistance >> Resr and Rdc
Figure 11. Voltage Mode Control Loop with Loop Dynamic for Type III Compensation
The simple guidelines for positioning the poles and zeros and for calculating the component values for Type III compensation are as follows:
5
a. b. c. d. e. f. g. h. i.
Choose fco = fs / 10 Calculate fp_LC fp_LC = 1 / 2 [(L) (C)] ^ 1/2 Calculate fz_ESR fz_ESR = 1 / 2 (Resr) (Cout) Select R1 component value such that 50k R1 100k Calculate R2 base on the desired Vout R2 = R1 / [(Vout / 0.80V) - 1] Select the ratio of Rz2 / R1 gain for the desired gain bandwidth Rz2 = R1 (Vramp_pp / Vin_max) (fco / fp_LC) Calculate Cz2 by placing the zero at 1/2 of the output filter pole frequency Cz2 = 1 / (Rz2) (fp_LC) Calculate Cp1 by placing the first pole at ESR zero frequency Cp1 = 1 / 2 (Rz2) (fz_ESR) Calculate Rz3 by setting the second pole at 1/2 of the switching frequency and the second zero at the output filter double pole frequency Rz3 = 2 (R1) (fp_LC) / fs Calculate Cz3 from Rz3 component value above Cz3 = 1 / (Rz3) (fs) Choose 100pF Cf1 220pF to stabilize the SP7650ER internal Error Amplify
j. k.
As a particular example, consider for the following SP7650EB with a Type III Voltage Loop Compensation component selections: Vin = 5 to 15V Vout = 3.30V @ 0 to 3A load Select L = 6.8uH => yield 40% of maximum 3A output current ripple. Select Cout = 22uF Ceramic capacitor (Resr 4m) fs = 300khz SP7650 internal Oscillator Frequency Vramp_pp = 1.0V SP7650 internal Ramp Peak to Peak Amplitude Step by step design procedures: a. b. c. d. fco = 300khz / 5 = 60khz fp_LC = 1 / 2 [(6.8uH)(22uF)]^1/2 15khz fz_ESR = 1 / 2 (2m)(22uF) 3.6Mhz R1 = 68.1k, 1% 6
e. f. g. h. i. j. k.
R2 = 68.1k / [(3.30V / 0.80V) - 1] 21.5k, 1% Rz2 = 68.1k (1.0V / 15V) (60khz / 15khz) 15k, 1% Cz2 = 1 / (18k) (20khz) 1,000pF, X7R Cp1 = 1 / 2 (15k) (3.6Mhz) 10pF => Select Cp1 = 22pF for noise filtering Rz3 = 2 (68.1k) (15khz) / 300khz 7.15k, 1% Cz3 = 1 / (7.15k) (300khz) 100pF, COG Cf1 = 100pF to stabilize SP7650ER internal Error Amplify
+5V INPUT WITH A TYPE III COMPENSATION APPLICATION SCHEMATIC Figure 12 shows another example of SP7650ER configures for +5V input by simply changing a few external resistors and capacitors components value for delivering a 03A output with excellent line and load regulation.
U1 SP7650
1 PGND PGND PGND GND VFB COMP UVIN GND SS VIN VIN VIN VIN LX LX LX LX VCC GND GND GND BST NC LX LX LX 26 25 24 23 22 21 20 19 18 17 16 15 14 2 3 4 5 6 7 8 9
L1 6.8uH C3 22uF 6.3V RZ3 7.15k,1% CZ3 150pF
VOUT 3.30V 0-3A
R1 68.1k,1%
CZ2
RZ2
1,000pF 15k,1% CP1 22pF CF1 100pF fs=300Khz
CVCC 2.2uF 20 SD101AWS DBST CBST 6,800pF
GND2
C3 CERAMIC 1210 X5R R2 21.5k,1%
CSS 47nF
10 11 12 13
RBST
5V VIN
C1 CERAMIC 0805 C1 X5R 22uF 6.3V
R3 100k,1%
Notes:
U1 Bottom-Side Layout should has three Contacts which are isolated from one of another, QT & QB Drain Contact and Controller GND Contact All resistor & capacitor size 0603 unless other wise specify
GND
C2 0.1uF
Figure 12. SP7650ER Configures for Vin = 5V, Vout = 3.3V at 0-3A Output Load Current
7
PC LAYOUT DRAWINGS
Figure 13. SP7650EB Component Placement
Figure 14. SP7650EB PC Layout Top Side
Figure 15. SP7650EB PC Layout 2nd Layer Side
8
Figure 16. SP7650EB PC Layout 3rd Layer Side
Figure 17. SP7650EB PC Layout Bottom Side
9
Table 2: SP7650EB List of Materials
8700 8700
0
ORDERING INFORMATION Model Temperature Range Package Type SP7650EB...................................-40C to +85C..................SP7650 Evaluation Board SP7650ER.................................. -40C to +85C.......................................26-pin DFN
10

▲Up To Search▲

Price & Availability of SP7650EB

	To Download SP7650EB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .